Sling Inspection Checklist: How to Inspect Before Every Lift

·

This is the practical companion to our guide on sling inspection and retirement: a step-by-step checklist you can easily run through on a job site, before the sling ever goes on a hook. Keep it simple: work through it in order, and if anything fails, the sling comes out of service.

Before You Start: Check the Tag

  • Is the identification tag present, attached, and legible?
  • Does it list a rated capacity for the hitch type you’re about to use (vertical, choker, or basket)?
  • Does the material and construction match what the job requires (e.g., not a nylon sling near acids, not a synthetic sling in high heat)?

If the tag is missing or unreadable, stop here. A sling without a readable rated capacity can’t be verified as safe for the load, no matter how good it looks.

Round & Webbing Slings: Visual and Hands-On Check

With gloves on, run the full length of the sling through your hands. Look and feel for:

  • Cuts, holes, tears, or punctures: especially any that expose the core yarns on a round sling or the load-bearing fibers on webbing.
  • Abrasive wear or snags: fuzzing, thinning, or a rough, worn patch anywhere along the body or at the eyes.
  • Broken or worn stitching: check the eyes and any load-bearing seams closely; loose or frayed thread is cause to remove from service.
  • Heat damage: melting, glazing, stiffness, or discoloration, particularly near sharp edges or hot equipment.
  • Chemical damage: brittle spots, discoloration, or a sticky/tacky feel that wasn’t there before.
  • Knots: any knot in the body of the sling (other than a factory core-yarn knot inside a round sling’s cover) is a removal condition.
  • Overall shape: any unusual lumps, soft spots, or uneven feel along a round sling’s length can indicate internal yarn damage even if the cover looks fine.
    • NOTE: the join in a round sling will feel like a lump and could be misleading. This callout specifically refers to lumps in unusual places.

Steel-Core Round Slings: Additional Checks

A steel-core round sling uses the same protective cover construction as a standard round sling, wrapped around a wire rope core. Run the checks above, then add these:

  • Broken core wires
  • Kinking, crushing, bird caging, or any other damage to the wire rope structure
  • Severe corrosion of the wire rope

Never run bare hands along a wire rope core to check it. A broken wire can puncture skin; inspect visually, or use gloves.

General Checks (All Sling Types)

  • Has the sling elongated or stretched noticeably compared to its original length?
  • Is there any doubt at all about the sling’s condition, even if nothing specific stands out?

If the answer to either of those is yes, remove the sling from service. “When in doubt, tag it out” isn’t just a slogan; it’s the actual standard.

How and When Inspections are Performed

Inspection typeWho performs itFrequencyWhat it catches
Initial inspectionA designated personOnce, before a new or repaired sling is first put in serviceWrong sling for the job, spec mismatch, shipping damage
Frequent inspectionThe user handling the slingEvery time it’s usedObvious damage: cuts, burns, missing tags, broken stitching
Periodic inspectionDesignated/qualified personnelBased on frequency of use and service severity; not to exceed 1 yearGradual wear, internal damage, and cumulative condition, documented in writing

The frequent, before-use check takes a minute and catches most problems. The periodic inspection is the one worth putting on a calendar and keeping a written record of, especially for crews running a formal safety program or a rental fleet, where documentation matters as much as the inspection itself.

Printable Checklist

Check itemPass / Fail
ID tag present, legible, rated capacity matches hitch type 
No cuts, holes, tears, or punctures 
No abrasive wear, fuzzing, or snags 
Stitching intact, no broken or worn threads 
No heat damage (melting, glazing, discoloration) 
No chemical damage (brittleness, stickiness, discoloration) 
No knots in the sling body 
No unusual lumps, soft spots, or elongation
(Steel-core only) No broken, kinked, crushed, or bird caged core wires
(Steel-core only) No severe corrosion of the wire rope
Overall: no doubt about continued use

Sources referenced: OSHA 29 CFR 1910.184; ASME B30.9-2021 inspection criteria; WSTDA-RS-1 Polyester Roundsling Standard; Liftin Gear Instructions for Use (Roundslings, Steel Core Roundslings, Web Slings), Rev A.

Other Topics